1、butt weld

butt weld發音

英：[b?t weld]　　美：[b?t weld]

英：　　美：

butt weld中文意思翻譯

常用釋義：對接焊接：通過對接焊接而形成的對接接頭。

對接焊縫；對頭焊接

butt weld雙語使用場景

1、By the analysis and measures above, it improves the test quality of the process piping butt weld effectively.───通過以上分析和采取的措施，能有效提高工藝管道對接焊縫超聲波檢測的質量。

2、Check whether the butt weld is smooth; there is any mismatch, or any other weld problem.───目視檢查焊接處是否平整，兩邊是否有錯位。以及是否有虛焊、焊脫現象。

3、Reducing long radius butt weld elbows shall be kept to a minimum.───應盡量少用長徑異徑對焊彎頭。

4、Dimensions - End-to-end dimensions for butt weld , two-way, globe- type, straight pattern control valves.───尺寸。對接焊接，兩向，球型，垂直模式控制閥的末端對末端尺寸。

5、Weld the outer side member with a full butt weld under shielding gas.───用氣體保護全對接焊，焊接外側梁。

6、The assembly deviation butt weld of has line on the part of the middle, the light is different on the sides of linear.───組對偏差的對接焊縫其焊縫偏中間區域會(huì )出現線條，線條兩側的亮度不同；

7、fatigue resistance of the scarf weld in the end of the vessel is stronger than that of the butt weld.───部斜面焊縫結構的抗疲勞強度比對接焊縫結構高，且不會(huì )發生一次性脆性破壞；

8、weld can be divided into four types: butt weld, fillet weld, plug weld and end weld.───焊縫可分為對接焊縫、角焊縫、塞焊縫和端接焊縫四種。

9、The other size and end connection - butt weld, socket weld and thread are available upon request.───其它尺寸及接口型式-承插焊，套焊及螺紋等可接受訂購

butt weld相似詞語短語

1、weld wheels───焊接車輪

2、butt plug───肛門插

3、butt out───別管閑事；不必多嘴

4、butt───n.(Butt)人名；(英)巴特；(俄、德、印、巴基)布特；n.屁股；煙頭；笑柄；靶垛；粗大的一端；vt.以頭抵撞；碰撞

5、weld together───焊接在一起

6、autogenous weld───氣焊

7、unfitness of butt weld───焊縫對口錯邊量

8、gouged weld───福利

9、fillet weld───角焊縫，填角焊，貼角焊

2、跪求壓力控制閥裝配

控制閥標準匯總

GB/T13852-1992

船用液壓控制閥技術條件

General specification of hydraulic control valves for ship

GB/T17490-1998

液壓控制閥油口、底板、控制裝置和電磁鐵的標識

Hydraulic fluid power--Identification of valve ports,subplates,control devices and solenoids

GB/T15623.1-2003

液壓傳動 電調制液壓控制閥 第1部分：四通方向流量控制閥試驗方法

Hydraulic fluid power-Electrically modulated hydraulic control valves-Part 1:Test methods for four-way directional flow control valves

GB/T15623.2-2003

液壓傳動 電調制液壓控制閥 第2部分：三通方向流量控制閥試驗方法

Hydraulic fluid power-Electrically modulated hydraulic control valves-Part 2:Test methods for three-way directional flow control valves

GB/T17213.7-1998

工業過程控制閥第7部分: 控制閥數據單

Industrial-process control valves Part 7: Control valve data sheet

GB/T17213.8-1998

工業過程控制閥第8部分: 噪聲的考慮第1節: 實驗室內測量空氣動力流流徑控制閥產生的噪聲

Industrial-process control valves Part 8: Noise considerations Section 1: Laboratory measurement of noise generated by aerodynamic flow through control valves

GB/T17213.1-1998

工業過程控制閥第1部分: 控制閥術語和總則

Industrial--Process control valves Part 1: Control valve terminology and general considerations

GB/T17213.5-1998

工業過程控制閥第5部分: 標志

Industrial-process control valves Part 5: Marking

GB/T2514-1993

四油口板式液壓方向控制閥安裝面

Hydraulic fluid power--Four-port directional control valves--Mounting surfaces

GB/T8104-1987

流量控制閥試驗方法

Hydraulic fluid power--Valves--Testing method of flow control valves

GB/T7940.3-2001

氣動五氣口方向控制閥第三部分: 功能識別編碼體系

Pneumatic fluid power--Five-port directional control valves--Part 3: Code system for communication of valve functions

GB/T8106-1987

方向控制閥試驗方法

Hydraulic fluid power--Valves--Testing method of directional control valves

GB/T7940.2-2001

氣動五氣口方向控制閥第二部分帶電氣接頭的安裝面

Pneumatic fluid power--Five-port directional control valves--Part 2: Mounting interface surfaces with optional elettrical connector

GB/T8105-1987

壓力控制閥試驗方法

Hydraulic fluid power--Valves--Testing method of pressure control valves

GB/T7940.1-2001

氣動五氣口方向控制閥第一部分: 不帶電氣接頭的安裝面

Pneumatic fluid power--Five-port directional control valves--Part 1: Mounting interface surfaces without electrical connector

GB/T8100-1987

板式聯接液壓壓力控制閥(不包括溢流閥)順序閥、卸荷閥、節流閥和單向閥安裝面

Hydraulic fluid power--Pressure control valves (excluding pressure relief valves ), sequence valves, unloading valves, throttle valves and check valves--Mounting surfaces

GB/T8098-2003

液壓傳動帶補償的流量控制閥安裝面

Hydraulic fluid power--Compensated flow control valves--Mounting surfaces

JB/T7387-1994(2005復審)

工業過程控制系統用電動控制閥

NF C46-520-1993

工業過程控制閥.第8部分:噪聲問題.第2節:通過控制閥的液壓流動產生的噪聲的實驗室測量

(Industrial-process control valves. Part 8 : noise considerations. Section 2 : laboratory measurement of noise generated by hydrodynamic flow through control valves.)

NF C46-522-1994

工業處理控制閥.第8部分:噪聲條款.第4節:液壓流動產生的噪聲預定(EN 534-8-4)

(Industrial-process control valves. Part 8 : noise considerations. Section 4 : prediction of noise generated by hydrodynamic flow.)

NF E49-080-1-2002

氣壓液動.五通定向控制閥.第1部分:不帶電連接器的安裝接口

(Pneumatic fluid power - Five-port directional control valves - Part 1 : mounting interfaces without electrical connector.)

NF E49-080-2-2002

氣壓液動.五通方向控制閥.第2部分:任選電氣連接器的安裝接口面

(Pneumatic fluid power - Five-port directional control valves - Part 2 : mounting interface surfaces with optional electrical connector.)

NF C46-505-1998

絕緣過程控制閥.第2-3部分:流量容量.試驗過程

(Industrial-process control valves. Part 2-3 : flow capacity. Test procedures.)

NF C46-630-1998

工業過程控制閥.第6部分:控制閥與定位器連接用安裝細節.第1節:線性傳動裝置上安裝的定位器

(Industrial-process control valves. Part 6 : mounting details for attachment of positioners to control valves. Section 1 : positioner mounting on linear actuators.)

NF E29-453-2000

工業過程控制閥門

(Industrial process control valves.)

NF E29-316-5-2001

供水用閥門.適用性要求和專用檢查試驗.第5部分:控制閥門

(Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 5 : control valves.)

NF C46-521-2001

工業過程控制閥.第8部分:噪聲問題.第3節:氣動控制閥噪聲預測法

(Industrial-process control valves - Part 8-3 : noise considerations - Control valves aerodynamic noise prediction method.)

NF E48-435-1998

液壓傳動.尺寸02、03和05的四端口模式排氣閥和四端口方向控制閥.夾緊尺寸

(Hydraulic fluid power. Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05. Clamping dimensions.)

NF C46-519-2001

工業過程控制閥.第8部分:噪聲考慮.第1節:實驗室測量氣動流經控制閥產生的噪聲

(Industrial-process control valves - Part 8 : noise considerations - Section 1 : laboratory measurement of noise generated by aerodynamic flow through control valves.)

NF C46-531-2001

工業過程控制閥.第6-2部分:定位器裝到控制閥的安裝細則.旋轉傳動裝置上安裝的定位器

(Industrial-process control valves - Part 6-2 : mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators.)

NF E49-091-2002

氣壓傳動.控制閥和其它部件的孔口和控制機械的驗證

(Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components.)

XP E29-140-1999

使用氣體燃料的家用裝置的控制閥.安全控制閥(帶有集中自動密閉器的)

(Control cocks for household appliances using gaseous fuels - Safety cocks (with integrated automatic obturator).)

NF C46-510-2001

工業過程控制閥.第3-1部分:尺寸.雙通球型直立式控制法蘭閥門的面對面尺寸和雙通球型角度控制法蘭閥門的中心

(Industrial-process control valves - Part 3-1 : dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, a)

NF C46-511-2001

工業過程控制閥.第3-2部分:尺寸.蝶閥除外的旋轉控制閥門的面對面尺寸

(Industrial-process control valves - Part 3-2 : dimensions - Face-to-face dimensions for rotary control valves except butterfly valves.)

NF E49-090-2-2003

氣壓傳動.18mm和26mm五氣口方向控制閥.第2部分:帶光學電接頭的安裝面

(Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 2 : mounting interfaces with optional electrical connector.)

NF C46-512-1999

工業處理控制閥.第3-3部分:尺寸.對焊接的頭尾相接尺寸.兩接頭球型直接式控制閥(歐洲標準EN 60534-3-3)

(Industrial-process control valves. Part 3-3 : dimensions. End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves.)

ANSI/IEEE 1290-1996

核發電站電動控制閥門馬達應用、防護、控制和試驗指南

(Guide for MOV (Motor-Operated Valve) Motor Application, Protection, Control, and Testing in Nuclear Power Generating Stations)

ANSI/FCI 87-2-1990

彈簧模板驅動控制閥動力信號標準

(Power Signal Standard for Spring-Diaphragm Actuated Control Valves)

ANSI/ISA 75.08.02-2003

無凸緣的控制閥端面間的尺寸(級別150、300和600)

(Face-to-Face Dimensions for Flangeless Control Valves (Classes 150, 300, and 600) )

ANSI/ISA S 75.08.03-2001

承插焊接端頭和螺旋端頭球狀控制閥的面到面尺寸

(Face-to-Face Dimensions for Socket Weld-End and Screwed-End Globe-Style Control Valves (ANSI Classes 150, 300, 600, 900, 1500, and 2500))

ANSI/ISA 75.08.06-2002

帶凸緣的球型控制閥體的面對面尺寸(類型900、1500和2500)

(Face-to-Face Dimensions for Flanged Globe-Style Control Valve Bodies (Classes 900, 1500, and 2500) )

ANSI/ISA 75.08.05-2002

端頭對焊球型控制閥的面對面尺寸(類型150、300、600、900、1500和2500)

(Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves (Classes 150, 300, 600, 900, 1500, and 2500) )

ANSI/ISA 75.01.01-2002

尺寸控制閥用流量方程式

(Flow Equations for Sizing Control Valves )

ANSI/ISA 75.08.01-2002

整體式帶凸緣的球型控制閥體的面對面尺寸(類型125、150、250、300和600)

(Face-to-Face Dimensions for Integral Flanged Globe-Style Control Valve Bodies (Classes 125, 150, 250, 300, and 600) )

ANSI/ISA S 75.19.01-2001

控制閥的靜水試驗

(Hydrostatic Testing of Control Valves)

ANSI/ISA S 75.08.04-2001

對焊端頭球狀控制閥的面到面尺寸

(Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves)

ANSI/ISA S 75.08.07-2001

獨立法蘭球狀控制閥的面到面尺寸

(Face-to-Face Dimensions for Separable Flanged Globe-Style Control Valves (Classes 150, 300, and 600))

ANSI/(NFPA) T 3.5.14 R1-1997

液力傳動.直接控制閥門.分界特性的測定方法

(Hydraulic Fluid Power - Directional Control Valve - Method for Determining the Metering Characteristics)

ANSI/(NFPA) T 3.21.8-1990

氣壓液動.反應時間的測量.直接控制閥門

(Pneumatic Fluid Power - Measurement of Response Time - Directional Control Valves)

ANSI/ISA S 75.15-1993

對焊端球狀控制閥的面對面尺寸(ANSI等級150、300、600、900、1500、2500)

(Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves (ANSI Classes 150, 300, 600, 900, 1500, and 2500))

ANSI/FCI 91-1-1997

控制閥門密封的質量標準

(Standard for Qualification of Control Valve Stem Seals)

ANSI/UL 753-1996

消防裝置用自動供水控制閥的警報附件

(Alarm Accessories for Automatic Water-Supply Control Valves for Fire-Protection Service)

BS EN 60534-2-5-2003

工業過程控制閥.流通能力.通過有段間恢復功能的多段控制閥的流體流量的校準公式

(Industrial-process control valves - Flow capacity - Sizing equations for fluid flow through multistage control valves with interstage recovery)

ASTM F 1985-1999

氣力操作的球形控制閥標準規范

(Standard Specification for Pneumatic-Operated, Globe-Syle, Control Valves)

BS EN 60534-3-2-2001

工業過程控制閥.尺寸.蝶形閥除外的轉式控制閥的端面距

(Industrial-process control valves - Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves)

BS ISO 15407-2-2003

氣壓傳動.五氣口方向控制閥,規格18mm和26mm.有任選電接頭的安裝接口

(Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Mounting interface surfaces with optional electrical connector)

BS ISO 12238-2001

氣壓液動.方向控制閥門.轉換時間的測量

(Pneumatic fluid power - Directional control valves - Measurement of shifting time)

BS ISO 5599-1-2001

氣壓液動.五通方向控制閥.不帶電連接器的安裝接口表面

(Pneumatic fluid power - Five-port directional control valves - Mounting interface surfaces without electrical connector)

BS ISO 5599-2-2001

氣壓液動.五通方向控制閥.任選電氣連接器的安裝接口面

(Pneumatic fluid power - Five-port directional control valves - Mounting interface surfaces with optional electrical connector)

BS EN 60534-6-2-2001

工業過程控制閥.定位器裝到控制閥的安裝細則.旋轉傳動裝置上安裝的定位器

(Industrial-process control valves - Mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators)

BS EN 1074-5-2001

供水閥門.適用性和專用要求的試驗.控制閥門

(Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Control valves)

BS EN 60534-8-3-2000

工業流程控制閥.噪聲問題.控制閥的空氣動力噪聲預報法

(Industrial-process control valves - Noise considerations - Control valve aerodynamic noise prediction method)

BS EN 60534-2-3-1998

工業過程控制閥.流量.試驗程序

(Industrial-process control valves - Flow capacity - Test procedures)

BS EN 60534-8-1-2001

工業過程控制閥.噪聲問題.通過控制閥的動力噪聲的實驗室測量

(Industrial-process control valves - Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves)

BS EN 60534-3-1-2000

工業過程控制閥.尺寸.帶法蘭的兩路、球型、直立式控制閥門的面對面尺寸和帶法蘭的兩路、球型、角度控制閥門

(Industrial-process control valves - Dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle patter)

BS EN 1349-2000

工業處理控制閥門

(Industrial process control valves)

BS ISO 15407-1-2000

18mm和26mm五氣口氣動方向控制閥.無電插頭的安裝界面

(Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Mounting interface surfaces without electrical connector)

BS ISO 11727-1999

氣動流體力學.控制閥和其它元件的控制機械裝置和氣門的識別

(Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components)

BS EN 60534-3-3-1998

工業過程控制閥.尺寸.對接焊接,兩向,球型,垂直模式控制閥的末端對末端尺寸

(Industrial-process control valves - Dimensions - End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves)

BS EN 60534-2-1-1999

工業過程控制閥 .流容.安裝條件下液流規模方程

(Industrial-process control valves - Flow capacity - Flow capacity - Sizing equations for fluid flow under installed conditions)

BS ISO 6263-1997

液壓傳動.補償式流量控制閥.裝配面

(Hydraulic fluid power - Compensated flow-control valves - Mounting surfaces)

BS ISO 10770-2-1998

液壓傳動.電模式液壓控制閥.第2部分:三向流動控制閥的試驗方法

(Hydraulic fluid power - Electrically modulated hydraulic control valves - Test methods for three-way directional flow control valves)

BS ISO 10770-1-1998

液壓傳動.電模式液壓控制閥.第1部分:四向流動控制閥的試驗方法

(Hydraulic fluid power - Electrically modulated hydraulic control valves - Test methods for four-way directional flow control valves)

BS EN 60534-6-1-1998

工業過程控制閥 .控制閥調節器連接用安裝元件.直線傳動裝置上調節器的安裝

(Industrial-process control valves - Mounting details for attachment of positioners to control valves - Positioner mounting on linear actuators)

BS ISO 7790-1998

液壓傳動.規格為03和05型的四油口標準設計疊閥和四油口定向控制閥.緊固尺寸

(Hydraulic fluid power - Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05 - Clamping dimensions)

EN 60534-8-1-2000

工業過程控制閥 第8部分：噪聲的考慮 第1節：氣動流流徑控制閥產生的噪聲的實驗室測量

Industrial-process control valves - Part 8: Noise consideration; Section 1: Laboratory measurement of noise generated by hydrodynamic aerodynamic flow through control valves (IEC 60534-8-1:1986)

EN 60534-8-4-1994

工業過程控制閥 第8部分：噪聲問題 第4節：流動產生的噪聲的預測

Industrial-process control valves - Part 8: Noise considerations - Section 4: Prediction of noise generated by hydrodynamic flow (IEC 60534-8-4:1994)

EN 60534-8-3-2000

工業流程控制閥 .第8-3部分 噪聲問題 通過控制閥的動力噪聲預測法

Industrial-process control valves - Part 8-3: Noise considerations; Control valve aerodynamic noise prediction method (IEC 60534-8-3:2000)

EN 1074-5-2001

供水閥門 目的要求的適應性和合適的認證試驗 第5部分：控制閥門

Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 5: Control valves

EN 60534-3-1-2000

工業過程控制閥 第3－1部分：尺寸 法蘭雙通球形直型控制閥的端面間距尺寸和有法蘭雙通球型角型控制閥的

Industrial-process control valves - Part 3-1: Dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, angle pattern control valves (IEC 60534-3-1:2000)

EN 60534-2-1-1998

工業過程控制閥 第2－1部分：流通能力 安裝條件下流體流量的校準公式

Industrial-process control valves - Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions (IEC 60534-2-1:1998)

EN 60534-1-1993

工業過程控制閥 第1部分 控制閥術語和一般考慮

Industrial-process control valves - Part 1: Control valve terminology and general considerations (IEC 60534-1:1987)

EN 60534-3-2-2001

工業過程控制閥 第3部分：尺寸 第2節：無法蘭控制閥（薄型蝶閥除外）的端面間距尺寸

Industrial-process control valves - Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves (IEC 60534-3-2:2001)

EN 60534-3-3-1998

工業過程控制閥 第三部分：尺寸 對接焊接 兩向 球型 垂直模式控制閥的末端對末端尺寸

Industrial-process control valves - Part 3-3: Dimensions - End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves (IEC 60534-3-3:1998)

EN 60534-6-1-1997

工業過程控制閥 第6－1部分：定位器聯到控制閥執行機構的安裝細則 第1節：直線傳動裝置上調節器的安裝

Industrial-process control valves - Part 6: Mounting details for attachment of positioners to control valves - Section 1: Positioner mounting on linear actuators (IEC 60534-6-1:1997)

EN 60534-6-2-2001

工業過程控制閥 第6－2部分：定位器聯到控制閥執行機構的安裝細則 環形執行機構定位器

Industrial-process control valves - Part 6-2: Mounting details for attachment of positioners to control valves; Positioner mounting on rotary actuators (IEC 60534-6-2:2000)

EN 60534-8-2-1993

工業過程控制閥 第8部分 噪聲考慮 第2節通過控制閥的流體產生的噪聲的實驗室測量報法

Industrial-process control valves- Part 8: noise consideration- Section 2: laboratory measurement of noise generated by hydrodynamic flow through control valves (IEC 60534-8-2:1991)

EN 60534-2-3-1998

工業過程控制閥 第2部分：流通能力 第3節：試驗規程

Industrial-process control valves - Part 2-3: Flow capacity - Test procedures (IEC 60534-2-3:1997)

prEN 13959-2000

公稱壓力在DN6至DN250（含DN250）的防污染控制閥 E族A、B、C和D型

Anti-pollution check valves DN 6 to DN 250 inclusive - Family E, type A, B, C and D

prEN 60534-4-1998

工業過程控制閥 第4部分：檢驗和常規試驗 草案

IEC 60534-4: Industrial-process control valves - Part 4: Inspection and routine testing

EN 1349-2000+AC-2001

工業加工控制閥門

Industrial process control valves

EN 60534-2-5-2003

工業加工控制閥 第2-5部分：流量 通過帶級間恢復多級控制閥的流體尺寸方程

Industrial-process control valves - Part 2-5: Flow capacity; Sizing equations for fluid flow through multistage control valves with interstage recovery (IEC 60534-2-5:2003) / Note: Endorsement notice

BS ISO 4401-1996

液壓傳動.四油口定向控制閥.裝配面

(Hydraulic fluid power - Four-port directional control valves - Mounting surfaces)

BS EN 60534-1-1989

工業過程控制閥 .第1部分:控制閥術語和一般考慮

(Industrial-process control valves - Industrial-process control valves - Control valve terminology and general considerations)

BS EN 60534-8-4-1994

工業過程控制閥.第8部分:噪聲問題.第4節.流動產生的噪聲的預報

(Industrial-process control valves - Noise considerations - Prediction of noise generated by hydrodynamic flow)

BS EN 60534-8-2-1991

工業過程控制閥.第8部分:噪聲考慮.第2節:通過控制閥的流體產生的噪聲的實驗室測量

(Industrial-process control valves - Noise considerations - Laboratory measurement of noise generated by hydrodynamic flow through control valves)

BS 6494-4-1989

液壓閥的安裝面.第4部分:03和05規格的四孔組件排氣閥、模數組閥和方向控制閥夾緊尺寸規范

(Hydraulic fluid power valve mounting surfaces - Specification for clamping dimensions of four-part, size 03 and 05, modular stack valves and directional control valves)

BS 5793-4-1987

工業過程控制閥.第4部分:檢驗和例行試驗規范

(Industrial-process control valves - Specification for inspection and routine testing)

BS 5944-4-1984

液壓動力系統和部件所產生的空氣噪音的測量.第4部分:流量和壓力控制閥聲功率級的測定方法

(Measurement of airborne noise from hydraulic fluid power systems and components - Method of determining sound power levels from valves controlling flow and pressure)

BS 5793-5-1984

工業過程控制閥.第5部分:標記規范

(Industrial-process control valves - Specification for marking)

BS 1655-1950

過程控制工業用法蘭連接自動控制閥(面至面尺寸)規范

(Specification for flanged automatic control valves for the process control industry (face-to-face dimensions))

DIN EN 60534-2-3-1998

工業過程控制閥.第2-3部分:流量.檢驗方法

(Industrial-process control valves - Part 2-3: Flow capacity; test procedures (IEC 60534-2-3:1997); German version EN 60534-2-3:1998)

DIN EN 60534-6-1-1998

工業流程控制閥.第6部分:調節閥門驅動的位置調節器固定用